Watch Your Temperatures

by Ethan Schneider

Summer temperatures can affect your CTI products, especially sealers.

All CTI sealers are tested in a variety of different environments ranging from extreme cold to extreme heat. The figures that are provided on each product spec sheet for cure times, pot life, re-coat window times, and application procedures are all based on an average temperature of 77 degrees Fahrenheit.

If you store your products in your trailer and it is 90 degrees outside, your products are likely to hit temperatures close to 120 degrees. High temperatures can drastically affect pot life of two component products especially epoxy resins such as Rapid Armor, Superseal 210, Enviroprime, and 5000 Binder. Urethanes such as Aquathane 6000 and Pro-seal 200 can also be affected. Prolonged exposure of your products to high temperatures can also significantly shorten their shelf life.

Before using these products, it is recommended that you make sure the products are brought to the proper temperature range before mixing and application. For most products that range is between 70 and 80 degrees Fahrenheit.

There are a couple of ways to insure that your products are in the proper temperature range before application.

1. Try to store the products in the environment where they are going to be applied for several hours before the application.
2. Store the products in the air conditioned cab of your truck on your way to the job site.

Watch you temperatures

by Ethan Schneider

Summer temperatures can affect your CTI products, especially sealers.

All CTI sealers are tested in a variety of different environments ranging from extreme cold to extreme heat. The figures that are provided on each product spec sheet for cure times, pot life, re-coat window times, and application procedures are all based on an average temperature of 77 degrees Fahrenheit.

If you store your products in your trailer and it is 90 degrees outside, your products are likely to hit temperatures close to 120 degrees. High temperatures can drastically affect pot life of two component products especially epoxy resins such as Rapid Armor, Superseal 210, Enviroprime, and 5000 Binder. Urethanes such as Aquathane 6000 and Pro-seal 200 can also be affected. Prolonged exposure of your products to high temperatures can also significantly shorten their shelf life.

Before using these products, it is recommended that you make sure the products are brought to the proper temperature range before mixing and application. For most products that range is between 70 and 80 degrees Fahrenheit.

There are a couple of ways to insure that your products are in the proper temperature range before application.

1. Try to store the products in the environment where they are going to be applied for several hours before the application.
2. Store the products in the air conditioned cab of your truck on your way to the job site.

CTi Products and The Cold Weather

by Ethan Schneider

Winter is here and mother nature's grip on the northern states can be ferocious. It is very important for CTI dealers to pay attention to temperatures for two reasons:

Installation limitations and specs.

Storage of materials.

Even though the outside temperatures are below freezing in many areas it does not mean that you can't continue to do some exterior work. There are ways to create acceptable work conditions even when the temperatures are below freezing. Areas can be tented and heated with propane heaters such as Salamanders or torpedo type heaters. Also bare concrete slabs can be heated with a propane torch just prior to skim coating . When working in colder temperatures remember to use 111 Quickset modifier. Note: 111 Quick set modifier can be combined with CTI's new 112 modifier at a 1 to 1 ratio. In other words ½ and ½.

Working with sealers in colder temperatures can be a bit more challenging. Both epoxies and urethanes should not be applied below 50 degrees. This is referring to the temperature of the slab, which is usually at least 5 degrees lower than the ambient air temperature. Since both of these types of products are usually installed inside, there are a few points to keep in mind.
The spec sheets provided for CTI sealers on the dealer website contain cure time information that is based on an average temperature of 77 degrees in a perfect laboratory environment. If you are applying epoxies or urethanes on interior jobs at lower temperatures between 50 and 77 degrees the cure and re-coat window times will be extended. The extended times may be twice as long depending on temperature, humidity, air movement, and ventilation. The point is to allow for additional cure time when working in lower temperatures.

Be careful when driving around with product in your truck or trailer when the temperatures are below freezing. Exposure to freezing temperatures even for a relatively short period of time may result in damaged product. Products such as modifiers 110,111,112 modifiers, 190 colorants, Aquathane 6000, 5000 Binder, Rapid Armor, Super seal 210, Eurobond colorants, Eurobond liquid bonding agent are all susceptible to damage from freezing. This applies to your product storage location as well. The storage location should kept above freezing.

If you have any questions about installation or storage of products in cooler temperatures please call the CTI tech department.